DIY Heated Dual Towel Rack

My nearly-new house was mis-designed so that the master bathroom had no windows that would open.  In the summer, this makes it difficult for towels to dry, so I added a heated towel rack.  When my girlfriend moved in, and chose to use two towels at one time, I needed a Plan B.

I looked around for heated towel racks, but they are either ridiculously expensive, cheaply made, or of the wrong size for my particular room.  I explored heating technologies, and found a product that is intended to be used to heat the bottoms of reptile tanks.  It comes in a 11 inch wide roll of heavy-duty plastic, with a power buss along each edge.  When you attach 110 V A/C (wall voltage) to the two power busses, the heating resistors in the sheet produce 20 watts per linear foot.  You can cut the roll to any length you wish (I used 2 foot lengths) to get as much or as little heat as you require.  The material looks like this:

You can find out more about this product, and purchase it from, www.reptilebasics.com.

I decided to buy some pieces of glass, mount (tape) the plastic material to the glass, and then drape the towels over the glass.  I cut some slots in some wood and dropped the glass into the slots.  The first prototype looked like this:

This shows how the wood was slotted:

This shows the bottom.  I intended to have the two towel warmers side by side, so I cut holes to allow air to circulate between the two towels.  At this point, only one heating plate was installed:

This shows the first prototype with the towel removed:

You can see the two 2-foot long pieces of heating material, taped to the glass with aluminum tape; two other pieces of heating material were used on the other side. The blue masking tape was used to reduce the chance that someone would accidentally brush up against the 110 V A/C connections.

We used this for a week or two. The heat produced was great for drying the towels, but this particular design has a number of problems.  For one thing, the two heating plates would have been too close to easily allow the towels to be draped into the space between the plates, and expanding that space made the unit take up too much floor space.  For another, it consumed more power than I wanted to use continuously (320 watts).  I considered about 5 different alternate designs, and chose one with the second towel directly above the first. This is how it looks, installed:

Notice the space between the towels, to allow access to the wall switches.  This is one reason that I decided to build a custom system. This is what it looks like with the towels removed:

I solved the power consumption problem by purchasing an ELK-960 delay timer, and modifying it so that the maximum time increased from 1 hour to 3 hours.  When you push a button, the timer and heaters come on for 3 hours, and then shut off.   You can see the button and activity LED here:

The bulk of the wiring is hidden behind the bottom panel.  You can see the 12 V power supply for the ELK board on the right, with the ELK board in the middle:

At some point, I may replace the wire nuts with soldered joints, and then enclose the solder in silicone caulk.  Not up to code, but safe enough for careful use by two adults. I attached the top of the rack to the wall with two lengths of chain, to ensure that it does not topple over.

Advertisements

2 Responses to “DIY Heated Dual Towel Rack”

  1. Ethan Olrich Says:

    Thanks for your write-up. I also believe laptop computers have grown to be more and more popular right now, and now are sometimes the only sort of computer found in a household. This is due to the fact that at the same time they are becoming more and more economical, their computing power keeps growing to the point where they’re as strong as desktop coming from just a few in years past. Take a look at my blog anytime. =).

  2. John Doe (Faraday Defcon) Says:

    DO NOT SOLDER. Keep the wire nuts. As an electrician, I cant stress this enough. Solder on connections that have any amount of current in them will get hot, and the solder can melt, leaving the wires exposed. Tip: When using wire nuts, do NOT twist the wires first. Let the nut do that. Pull on the nut when done. If it comes off, try again or go “down” a size in nut.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s


%d bloggers like this: